Insulated concrete formwork
We have doubled the grant rates for short course tiers 1 – 3. To address rising costs, you can now receive higher rates on course achievements from 1st April 2023
|
Grant Tier |
Achievement date before 1 April 2023 |
Achievement date on or after 1 April 2023 |
|
Grant Tier 1 Grant Tier 1 Refresher |
£30 £15 |
£60 £30 |
|
Grant Tier 2 Grant Tier 2 Refresher |
£70 £35 |
£140 £70 |
|
Grant Tier 3 Grant Tier 3 Refresher |
£120 £60 |
£240 £120 |
Overview
Standard details
CITB has developed this standard in discussion with industry
Duration
2 days of 6 learning hours
Purpose/Scope
The purpose of this standard is to provide the delegate with the knowledge to support the following:
Scope:
- project and process overview
- checklists (materials, safety, tools, measurement, equipment, literature etc.)
- preparation and planning
- installation
- pre-pour and pour
- tips and techniques
- quality assurance, site visits, certification
Occupational relevance
Training delivered against this standard would be relevant to the following occupational group(s):
- operative and craft
- supervision
Delegates pre-requisites
There are no delegate pre-requisites as part of this standard.
Instruction/Supervision
As a minimum, course trainers must be able to demonstrate that, in relation to this standard, they have:
- an award in education and training (or equivalent, as per requirements for approved training organisations)
- successfully completed training to this standard
- at least 2 years relevant industrial experience
- a verifiable CV
Delivery
Delivery may be in an on or off the job environment.
All materials and equipment must be of a suitable quality and quantity for delegates to achieve learning outcomes and must comply with relevant legislation.
The class size and delegate/trainer ratio must allow training to be delivered in a safe manner and enable delegates to achieve the learning outcomes.
The following delivery methods may be used in the delivery of this standard:
- classroom
This standard is considered to contain 51% or more practical training.
This standard is considered to be set at an intermediate level.
Assessment
Methods of assessment considered appropriate for training delivered against this standard are:
For the successful completion of training, the trainer must be satisfied that the delegate has achieved all learning outcomes.
Quality assurance
Assured
Quality assurance against this standard will require initial approval of the training organisation and their content mapped to the standard.
CITB will also conduct an approval intervention, either desk-based or centre visit, to ensure the training organisation can meet the requirements of the training standard.
Approved training organisations (ATOs) will be required to present information on records of training and assessment upon request to CITB for desk-based analysis. They will also be visited annually by the CITB quality assurance team.
Renewal/refresher
There are no mandatory renewal or recommended refresher requirements for this standard.
Classification
Lifetime
(Please note standards using this classification will only be grant aided once per delegate)
Approval date
December 2021
Review cycle
On request or 3 years from approval date.
Learning outcomes
The delegate will be able to:
- review the stages/steps of the project
- describe the process
- explain the planning and preparation activities that need to be completed
- Checklists (materials, safety, tools, measurement, equipment, literature etc.)
- manage their role in the installation process
- carry out their role in pre-pour planning
- carry out their designated role in the pour
- describe best practice activities
- carry out quality assurance activities, including supporting site visits and certification
Additional information about this standard
UK Certification Authority for Reinforcing Steels (CARES)
Health & Safety Executive (HSE) guides:
- Health & Safety at Work etc Act 1974
- Health and safety in construction
- PPE
- PUWER
- COSHH
- RIDDOR
- LOLER
- CDM
- Manual handling
- Noise
- Hand-arm vibration
- Electrical
Legislation
- Health and Safety at Work etc Act (HSWA) 1974
- The Work at Height Regulations (WHR) 2005
- Work at Height (Amended) 2007
- Personal Protection Equipment (PPE) Regulations 2002
- Personal Protection Equipment (PPE) at Work Regulations 1992
- Provision and Use of Work Equipment Regulations (PUWER) (1998 UK 1999 NI)
- Control of Substances Hazardous to Health Regulations (COSHH) 2002
- Lifting Operations and Lifting Equipment Regulations (LOLER) 1998
- Reporting of Injuries, Diseases and Dangerous Occurrences Regulations (RIDDOR) 1995
- Construction (Design and Management) Regulations (CDM) 2015
- Construction (Health, Safety and Welfare) Regulations 1996
- Manual Handling Operations Regulations 1992 as amended 2002
- Control of Noise at Work Regulations 2005
- Control of Vibration at Work Regulations 2005.
Related standards
- Concrete identity testing
- Concrete aggregates awareness
- Concrete polishing
- Concrete strength assessment
- Concrete placing compacting and finishing
- Cold weather concreting
- Identifying blemishes defects and deteriorating concrete
- Introduction to concrete and its constituents
- Industrial concrete flooring laser screeder operator
- Post-tensioning theory and practice refresher
- Post tensioning for supervisors
- Post-tensioning theory and practice
- Reinforced concrete for engineers and supervisors
- Supervision of concrete pumping operations
- Specifying concrete and receiving onsite
- Visual concrete perception practicalities and specifying