PREVIEW: Interlocking tiling


Overview
This preview is for ATOs only. The purpose of this standard is to provide the candidate with the knowledge and skills to install interlocking tiles for a new roof, including the: membrane, battens, main tiles, ridge tiles, hip tiles, verge tiles, valley tiles, fittings, and flashings.

This standard is available to ATOs to preview before it’s finally published. You should make sure your course matches these details. This standard will eventually supersede the existing standard in development. 

Until then, continue to publicise your courses against the existing title on the Construction Training Directory.

CITB has developed this standard in discussion with industry

Duration

Minimum 3 days of 6 learning hours

Purpose / scope

The purpose of this standard is to provide the candidate with the knowledge and skills to install interlocking tiles for a new roof, including the: membrane, battens, main tiles, ridge tiles, hip tiles, verge tiles, valley tiles, fittings, and flashings.

The scope of this advanced standard covers:

  • use of a roofing rig with a valley and a hip
  • practical training using one or more types of interlocking tile type/size for the time available
  • interlocking tiling system: tiles, fasteners, fixings, tile fixing methods, ridge tiles, ornamental ridge tiles, hip tiles, verge tiles, vented tiles, fittings, abutments, inclined valleys, valley tiles, insulation, flashings, junctions
  • interpret instructions and drawings
  • tools and equipment (hand & power)
  • perform basic estimates for materials
  • perform basic calculations for batten spacing
  • make a gauging stick
  • calculate side lap for tiles
  • make a marking stick
  • storage, handling, and lifting
  • plan the work
  • work safely
  • roof check
  • set out
  • install: membrane, battens, main tiles, ridge tiles, hip tiles, verge tiles, valley tiles, fittings, and flashings
  • mark and cut tiles
  • allow for a soil pipe penetration
  • maintain a clean and tidy workplace
  • if the weather deteriorates
  • clean up and dispose of waste materials.

Occupational relevance

Training delivered against this standard is relevant to the following occupational group(s):

  • operative and craft.

Candidate prerequisites

The candidate must have completed the interlocking tiles introduction training course.

Before candidates perform the work on a construction site, candidates must have successfully completed roofing-specific training for working safely at height.

Instruction / supervision

As a minimum, course instructors must be able to demonstrate that, in relation to this standard, they have:

  • A train the trainer or instructional techniques course certificate
  • Successfully completed training to this standard 
  • At least 2 years relevant industrial experience
  • A verifiable CV.

Delivery

The following method(s) may be used in the delivery of this standard:

  • classroom and workshop

All materials and equipment must be of a suitable quality and quantity for candidates to achieve learning outcomes, and must comply with relevant legislation.

The class size and candidate/instructor ratio must allow training to be delivered in a safe manner and enable candidates to achieve the learning outcomes.

This standard is considered to contain 51 per cent or more theoretical learning.

Assessment

For the successful completion of training, candidates must complete an end of course practical assessment or knowledge test that measures the learning outcomes and has a pass or fail criteria.

Quality assurance

Quality assurance against this standard will require initial approval of the training organisation and their content mapped to the standard. 

CITB will also conduct an approval intervention, either desk-based or centre visit, to ensure the training organisation can meet the requirements of the Training Standard. 

Approved training organisations (ATOs) will be required to present information on records of training and assessment upon request to CITB for desk-based analysis. They will also be visited annually by the CITB quality assurance team.

Renewal/refresher

There are no mandatory renewal or recommended refreshment requirements for this standard.

Approval date

TBC

Review cycle

Either on request or in 3 years from approval date.

Learning outcomes

The candidate will be able to Additional guidance to support learning outcome

Describe the plain tiling system features including:

  • tile types, uses, and materials
  • fasteners, fixings, and fixing methods (dry and bedded)
  • valleys, hips, verges, and ridges
  • membranes, battens, ridge tiles, hip tiles, verge tiles, vented tiles, fittings, abutments, valley tiles, insulation, flashings, junctions

Manufacturer’s:

  • brochure
  • installation information

Samples of:

  • plain tiles
  • fasteners
  • fixings
  • ridge tiles
  • verge tiles

Interpret simple instructions and drawings

Examples of:

  • manufacturer’s instructions
  • roofing drawings

Use tools and equipment (hand & power) for:

  • measuring, marking, cutting, and installing

Examples of tools and equipment

Perform basic calculations for batten spacings including:

  • bottom datum, top datum, and gauge

Sample calculations

Make and use a gauging stick

Example of a gauging stick

Perform basic calculations for side lap

Sample calculations

Make and use a marking stick

Example of a marking stick

Work safely including:

  • follow safe work practices/procedures
  • identify hazards
  • reduce/eliminate risks
  • use controls
  • use personal protective equipment (PPE)

Videos/photos of good and bad practice.

Examples of:

  • PPE
  • risk assessments
  • safe work practices/procedures

Roof check including:

  • defects, slope angle, spacings, dimensions, squareness and compensation techniques

 

Install stop battens and counter battens

Video in classroom

Practical demonstration in workshop using a roof rig

Candidate practice with coaching using a roof rig

Install tiles including:

  • main roof area, ridge, and verge

Mark and cut tiles using hand and power tools

Maintain a clean and tidy workplace

 

Describe what to do if the weather deteriorates including:

  • hot, cold, windy, and wet

 

Clean up and dispose of waste materials

Environmental considerations for waste materials

Additional information about this standard

Training at height

  • BS 8454:2006 Code of practice for delivery of training & education for work at height and rescue

Advisory Committee for Roof Safety

Work at Height Safety Association

  • View WAHSA technical guidance notes. These are a free resource, provided and maintained by WAHSA and its member companies for reference. They assist specifiers, managers, and end users of fall protection equipment. 

Health and Safety Executive (HSE) Working at height guides

HSE guides

Legislation

See relevant legislation

  • Health and Safety at Work etc Act (HSWA) 1974
  • The Work at Height Regulations (WHR) 2005
  • Work at Height (Amended) 2007
  • Personal Protection Equipment (PPE) Regulations 2002
  • Personal Protection Equipment (PPE) at Work Regulations 1992
  • Provision and Use of Work Equipment Regulations (PUWER) (1998 UK 1999 NI)
  • Control of Substances Hazardous to Health Regulations (COSHH )2002
  • Lifting Operations and Lifting Equipment Regulations (LOLER) 1998
  • Reporting of Injuries, Diseases and Dangerous Occurrences Regulations (RIDDOR ) 1995
  • Construction (Design and Management) Regulations (CDM) 2015
  • Construction (Health, Safety and Welfare) Regulations 1996
  • Manual Handling Operations Regulations 1992 as amended 2002
  • Control of Noise at Work Regulations 2005
  • Control of Vibration at Work Regulations 2005

Building regulations

  • Building and Buildings, England and Wales: The Building Regulations 2010.
  • The Building (Scotland) Regulations 2004
  • Statutory Rules of Northern Ireland

British standards

View all available British Standards at the BSI website.

  • BS 6100-6: 2008 Building and civil engineering – Vocabulary – Part 6 Construction parts (roofs)
  • BS 5534: 2014+A2: 2018. Slating & tiling for pitched roofs and vertical cladding. Code of practice.
  • BS 743:1970. Specification for materials for damp-proof courses.
  • BS 8000-6: 2013. Workmanship on building sites. Code of practice for slating & tiling of roofs and claddings. Replaced By BS 8000-0:2014. Workmanship on construction sites. Intro and principles
  • BS 8612: 2018. Dry fixed ridge, hip, and verge systems for slating and tiling. Specification.
  • BS EN 1024: 2012. Clay roofing tiles for discontinuous laying. Geometric characteristics.
  • BS EN 12326-1: 2014. Slate & stone for discontinuous roofing & external cladding. Specs for slate
  • BS EN 1304: 2013. Clay roofing tiles and fittings. Product definitions and specifications.
  • BS EN 13748-2: 2004. Terrazzo tiles. Terrazzo tiles for external use
  • BS EN 490: 2011+A1: 2017. Concrete roof tiles & fittings for roof & wall cladding. Product specs.
  • BS EN 492: 2012+A2:2018. Fibre-cement slates and fittings. Product spec and test methods.
  • BS 5250: 2011+A1: 2016. Code of practice for control of condensation in buildings.
  • BS 8437: 2005 Code of practice for selection, use and maintenance of personal protection systems

National Building Specification (NBS)

  • A multi-volume subscription library of clauses covering most elements of building construction.

Building information modelling (BIM)

Grants

Find out how to claim a grant for short duration training courses

ATO course accreditation

Find out how to accredit a training course to a standard.

Web design by S8080