PREVIEW: Waterproof membrane roofing systems installation


Overview
This preview is for ATOs only. The purpose of this standard is to provide the candidate with the knowledge and skills to install waterproof membrane roofing systems.

This standard is available to ATOs to preview before it’s finally published. You should make sure your course matches these details. This standard will eventually supersede the existing standard in development. 

Until then, continue to publicise your courses against the existing title on the Construction Training Directory.

CITB has developed this standard in discussion with industry

Duration

Minimum 1 day of 6 learning hours

Purpose / scope

The purpose of this standard is to provide the candidate with the knowledge and skills to install waterproof membrane roofing systems.

The scope of this standard covers:

  • how to set out including: restraint at perimeters and abutments, and membranes
  • how to seam joint by hot air welding using hand and automatic methods
  • how to seam joint by solvent welding including attachment to fasteners
  • how to seam joint by adhesives and tapes
  • special techniques including: quality assess seams, 'T' joints, temporary seals, and lap edge sealants
  • how to mechanically fix membranes
  • main legislation, codes of practice, standards, and guidance.

Occupational relevance

Training delivered against this standard is relevant to the following occupational group(s):

  • operative and craft
  • supervision.

Candidate prerequisites

There are no candidate pre-requisites as part of this standard. However, a basic knowledge of single ply roofing terminology and techniques would be beneficial.

Instruction / supervision

As a minimum, course instructors must be able to demonstrate that, in relation to this standard, they have:

  • A train the trainer or instructional techniques course certificate
  • Successfully completed training to this standard 
  • At least 2 years relevant industrial experience
  • A verifiable CV.

Delivery

The following methods may be used in the delivery of this standard:

  • classroom and / or workshop

All materials and equipment must be of a suitable quality and quantity for candidates to achieve learning outcomes and must comply with relevant legislation.

The class size and candidate/instructor ratio must allow training to be delivered in a safe manner and enable candidates to achieve the learning outcomes.

This standard is considered to contain 51 per cent or more theoretical learning.

Assessment

For the successful completion of training, candidates must complete an end of course practical assessment or knowledge test that measures the learning outcomes and has a pass or fail criteria.

Quality assurance

Quality assurance against this standard will require initial approval of the training organisation and their content mapped to the standard. 

CITB will also conduct an approval intervention, either desk-based or centre visit, to ensure the training organisation can meet the requirements of the Training Standard. 

Approved training organisations (ATOs) will be required to present information on records of training and assessment upon request to CITB for desk-based analysis. They will also be visited annually by the CITB quality assurance team.

Renewal/refresher

There are no mandatory renewal or recommended refreshment requirements for this standard.

Approval date

November 2018

Review cycle

Either on request or in 3 years from approval date.

Learning outcomes

The candidate will be able to Additional guidance to support learning outcome

Describe how to set out including: restraint at perimeters and abutments, and membranes

Tools and equipment

Photos, illustrations and/or videos.

Manufacturer’s design documents and brochures

Samples on a mobile stand

Sectional-view illustrations of an installation

SPRA guidance. Sealants in single ply roofing (S7-17)

Welding guidance (S14-18)

Safety – Design considerations for reduced risk (S5-17)

Describe how to seam joint by hot air welding using hand and automatic methods

Describe how to seam joint by solvent welding including attachment to fasteners

Describe how to seam joint by adhesives and tapes

Describe special techniques including: quality assess seams, 'T' joints, temporary seals, and lap edge sealants

Describe how to mechanically fix membranes

List the main types of information for safe working

Safety legislation (H&SAWA, COSHH, PUWER, LOLER, Work at Height), HSE guidance, manufacturer’s documents, British/EN/ISO Standards, codes of practice, association guidance, building regulations, SDS sheets, company procedures, risk assessments

Additional information about this standard

Single Ply Roofing Association (SPRA)

SPRA sets the design standards for single ply roofing in the UK. You can view the following free guides on the SPRA website

  • Design guide for single ply roofing
  • Acoustic control
  • Adhesives
  • Falls and drainage for single ply roofs (S10-10)
  • Guarantees – Guidance for clients and designers (S4-17)
  • Homeowners guide 2017 (S12-17)
  • Membrane product substitution checklist (S3-17)
  • Non-destructive testing of single ply membrane roofing coverings (S8-17)
  • Protection of single ply membrane roofs-guidance and checklist (SDG13-17)
  • Recycling scoping study (2017)
  • Safety – Design considerations for reduced risk (S5-17)
  • Sealants in single ply roofing (S7-17)
  • Ten reasons to specify SPRA contractor (S2-17)
  • Welding guidance (S14-18)
  • Wind load design requirements for single ply roofing (S11b-17)
  • Wind loading – single ply roofing guide and checklist (S11a-16)

SPRA also publishes ‘Component quality schemes’ for materials and equipment. These take existing standards (BS and BS-EN) and apply specific levels of performance required in single ply applications:

  • Expanded polystyrene insulation boards for inverted roofs (CQS2B-17)
  • Expanded polystyrene insulation boards for roofing (CQS2A-17)
  • Extruded polystyrene insulation boards for roofing (CQS3-17)
  • Factory-manufactured single ply membrane gutters (CQS8-17)
  • Fall protection anchor devices (CQS9-17)
  • Mechanical fasteners for attachment of insulation and membranes (CQS5-17)
  • Rock mineral wool insulation boards for roofing (CQS4-17)
  • Roof access hatches (CQS7-17)
  • Rooflights (CQS6-17)
  • SPRA-IMA quality standards (CQS1-17)
  • Vacuum insulated roof panels (VIPS) for roofing applications (CQS10-17)

British Flat Roofing Council

  • Flat roofing: Design and good practice 1993

Advisory Committee for Roof Safety

Work at Height Safety Association

  • View WAHSA technical guidance notes. These are a free resource, provided and maintained by WAHSA and its member companies for reference. They assist specifiers, managers, and end users of fall protection equipment. 

Health and Safety Executive (HSE) Working at height guides

British-European standards

You can view British and European standards on the BSI website

Note: Currently there are no British standards that cover polymeric single ply waterproofing membranes.

  • BS 476-3: 2004. Fire tests on building materials and structures. Classification and test methods for roofs
  • BS-EN 1991-1-2 6399: Part 2:1997 Code of practice for wind loads
  • BS-EN 1991-1-4: 2005 + A1:2010 Eurocode 1. Actions on structures. General actions. Wind actions
  • BS 4841-4: 2006. Rigid polyurethane (PUR) and polyisocyanurate (PIR) products for building end-use applications. Specification for laminated insulation boards (roofboards) with auto-adhesively or separately bonded facings for use as roofboard thermal insulation under non-bituminous single-ply roofing membranes
  • BS 6399-2:1997. BS6399-2: 1997 Loading for buildings. Part 2: Code of practice for wind loads
  • BS 6229: 2003 Code of practice for flat roofs with continuously supported coverings
  • BS 8217: 2005 Reinforced membranes for roofing - Code of practice
  • BS 8437: 2005 Code of practice for select/use/maintain personal protection systems and equipment
  • BS 8454: 2006 Code of practice for delivery of training & education for work at height and rescue
  • BS-EN 12056-3: 2001 Part 3 Gravity drainage systems in buildings. Roof drainage, layout & calcs
  • BS-EN 13956: 2003 Flexible (plastic and rubber) sheets for roof waterproofing. Definitions/characteristics
  • HB 10139:1997. Wind loading ready reckoner for BS 6399: Part 2: 1997
  • DD CEN / TS 1187: 2012 Test methods for external fire exposure to roofs

Legislation

See relevant legislation

  • The Work at Height Regulations (WHR) 2005
  • Statutory Rules of Northern Ireland
  • The Building (Scotland) Regulations 2004
  • Building and Buildings, England and Wales: The Building Regulations 2010
  • Control of Substances Hazardous to Health Regulations (COSHH) 2002
  • Health and Safety at Work etc Act 1974
Share